Başlık için Endüstri Mühendisliği-Makale Koleksiyonu listeleme
Toplam kayıt 32, listelenen: 1-20
-
An assembly line design and construction for a small manufacturing company
(Emerald Group Publishing Limited, 2008)Purpose - This study seeks to present a simple assembly line design and its balance for a low-volume manufacturing company. Design/methodology/approach - The study presents experiences with the design and implementation ... -
Bir transformatör işletmesinde montaj ünitesinin ergonomik analizi
(2017)Montaj hatlarında tekrarlayan işler ve uygun olmayan pozisyonlarda yapılan çalışmalar kas-iskelet sistemi rahatsızlıklarına (KİSR)ve işgücü kayıplarına sebep olmaktadır. KİSR’nın önüne geçmek için montaj hatlarının ergonomik ... -
Decision making for facility layout problem solutions
(Pergamon-Elsevier Science Ltd, 1999)In this study, facility layout problems, solution requirements and decision analysis are summarized. Decision making steps of a common layout problem is given. Then developed approaches for the solutions are revised and ... -
Depolama alanlarında çalışanların çalışma pozisyonlarının incelenmesi
(2017)Yüksek depolama alanlarında çalışan işçiler sıklıkla yüksek raflara uzanmakta, bir platform olmaksızın yüksek raflara erişilmesi istendiğinde bazen tırmanma hareketlerini yapabilmektedirler. Uzanma durumunda bel omurlarında, ... -
An effective approach based on response surface methodology for predicting friction welding parameters
(Walter de Gruyter GMBH, 2016)The joining of dissimilar metals is one of the most essential necessities of industries. Manufacturing by the joint of alloy steel and normal carbon steel is used in production, because it decreases raw material cost. The ... -
Integrating ant colony and genetic algorithms in the balancing and scheduling of complex assembly lines
(Springer London Ltd, 2016)Different from a large number of existing studies in the literature, this paper addresses two important issues in managing production lines, the problems of line balancing and model sequencing, concurrently. A novel hybrid ... -
Investigating the benefits of using circular die springs instead of rectangular die springs
(Wiley-Blackwell, 2015)Die springs with rectangular cross section (rectangular die springs) are common in the industry. However, the production of rectangular die springs is difficult, and the cost of production is high. In this study, we examined ... -
An investigation of bending fatigue behavior for glass-fiber reinforced polyester composite materials
(Elsevier Sci Ltd, 2008)To investigate bending fatigue behaviors for glass-fiber reinforced polyester composite material, 800 g/m(2), 500 g/m(2),300 g/m(2), and 200 g/m(2) glass-fiber woven and 225 g/m2 450 g/m(2), and 600 g/m(2) randomly distributed ... -
An investigation on weldability of AISI 304 and AISI 1040 steels on friction welding
(Carl Hanser Verlag, 2010)In welding technology, joining processes of different materials, which have dissimilar crystal structures are difficult. Welding of different materials becomes very important to reduce costs. Furthermore, the friction ... -
İşletmelerdeki ISO 9001 uygulamalarının ' işgöreni güçlendirme üzerindeki etkilerini ' belirlemeye yönelik bir araştırma
(2003)Variations, which appear in interior and exterior environmental conditions, have obliged management understanding in companies to be transformed from being traditional to contemporary. Employee empowerment is one of the ... -
Mathematical Model And Agent Based Solution Approach For The Simultaneous Balancing And Sequencing Of Mixed-Model Parallel Two-Sided Assembly Lines
(Elsevier Science Bv, 2014)One of the key factors of a successfully implemented mixed-model line system is considering model sequencing problem as well as the line balancing problem. In the literature, there are many studies, which consider these ... -
A mathematical model and genetic algorithm-based approach for parallel two-sided assembly line balancing problem
(Taylor & Francis Ltd, 2015)Assembly lines are usually constructed as the last stage of the entire production system and efficiency of an assembly line is one of the most important factors which affect the performance of a complex production system. ... -
Mathematical modeling of carbon content and intercritical annealing temperature in dp steels by factorial design method
(Journal Iron Steel Research Editorial Board, 2014)2(k) factorial design is employed to find the mathematical relation between the carbon content and intercritical annealing temperature (TAT) in order to predict the responses namely martensite volume fraction (MVF), ... -
A new painting process for vessel radiators of transformer: wet-on-wet
(Taylor & Francis Ltd, 2016)The painting process of corrugated wall radiators of a distribution transformer is performed by a flow-down painting technique in the industrial field. This study has been prepared in accordance with ISO 12944-5. ... -
Optimal design of c-type passive filters based on response surface methodology for typical industrial power systems
(Taylor & Francis Ltd, 2013)In this article, a response surface methodology based approach is proposed for the optimal design of C-type passive filters that can be employed in typical industrial power systems. The purpose of the optimization process ... -
Optimization of cutting parameters in face milling with neural networks and taguchi based on cutting force, surface roughness and temperatures
(Taylor & Francis Ltd, 2013)Prediction of cutting parameters as a function of cutting force, surface roughness and cutting temperature is very important in face milling operations. In the present study, the effect of cutting parameters on the mentioned ... -
Optimization of pı parameters for dsp-based permanent magnet brushless motor drive using response surface methodology
(Pergamon-Elsevier Science Ltd, 2012)This paper proposes response surface methodology (RSM) for tuning Proportional Integral (PI) coefficients for a Permanent Magnet Brushless Direct Current (PMBLDC) motor drive. Overshoot and settling time data are obtained ... -
Performance comparison of residual control charts for trend stationary first order autoregressive processes
(2011)Data sets collected from industrial processes may have both a particular type of trend and correlation among adjacent observations (autocorrelation). Existing statistical control charts may individually cope with autocorrelated ... -
A regression control chart for autocorrelated processes
(2014)In this study, we present a new regression control chart which is able to detect the mean shift in a production process. This chart is designed for autocorrelated process observations having a linearly increasing trend. ... -
Regression control chart for determination of young's modulus: A case study
(2011)The fundamental problem while obtaining initial modulus (Young's modulus) of concrete in experimental studies is to determine the region on stress-strain curve that will be used in calculations of initial tangent. In the ...
